Data Sheet
ADP5042
Rev. A | Page 23 of 32
APPLICATIONS INFORMATION
BUCK EXTERNAL COMPONENT SELECTION
Trade-offs between performance parameters such as efficiency
and transient response can be made by varying the choice of
external components in the applications circuit, as shown in
Figure 66.
Inductor
The high switching frequency of the ADP5042 buck allows for
the selection of small chip inductors. For best performance, use
inductor values between 0.7 糎 and 3 糎. Suggested inductors
are shown in Table 11.
The peak-to-peak inductor current ripple is calculated using
the following equation:
L
f
V
V
V
V
I
SW
IN
OUT
IN
OUT
RIPPLE
?/DIV>
?/DIV>
?/DIV>
=
)
(
where:
f
SW
is the switching frequency.
L is the inductor value.
The minimum dc current rating of the inductor must be greater
than the inductor peak current. The inductor peak current is
calculated using the following equation:
2
)
(
RIPPLE
MAX
LOAD
PEAK
I
I
I
+
=
Inductor conduction losses are caused by the flow of current
through the inductor, which has an associated internal dc
resistance (DCR). Larger sized inductors have smaller DCR,
which may decrease inductor conduction losses. Inductor core
losses are related to the magnetic permeability of the core material.
Because the buck is high switching frequency dc-to-dc converters,
shielded ferrite core material is recommended for its low core
losses and low EMI.
Table 11. Suggested 1.0 糎 Inductors
Vendor
Model
Dimensions
(mm)
ISAT
(mA)
DCR
(m?
Murata
LQM2MPN1R0NG0B 2.0 ?1.6 ?0.9
1400
85
Murata
LQM18FN1R0M00B 1.6 ?0.8 ?0.8
150
26
Taiyo Yuden CBMF1608T1R0M
1.6 ?0.8 ?0.8 290
90
Coilcraft
EPL2014-102ML
2.0 ?2.0 ?1.4
900
59
TDK
GLFR1608T1R0M-LR 1.6 ?0.8 ?0.8 230
80
Coilcraft
0603LS-102
1.8 ?1.69 ?1.1 400
81
Toko
MDT2520-CN
2.5 ?2.0 ?1.2
1350
85
Output Capacitor
Higher output capacitor values reduce the output voltage ripple
and improve load transient response. When choosing this value,
it is also important to account for the loss of capacitance due to
output voltage dc bias.
Ceramic capacitors are manufactured with a variety of dielec-
trics, each with a different behavior over temperature and
applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary
temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are recom-
mended for best performance. Y5V and Z5U dielectrics are
not recommended for use with any dc-to-dc converter because
of their poor temperature and dc bias characteristics.
The worst-case capacitance accounting for capacitor variation
over temperature, component tolerance, and voltage is calcu-
lated using the following equation:
C
EFF = COUT ?/SPAN> (1 TEMPCO) ?/SPAN> (1 TOL)
where:
CEFF is the effective capacitance at the operating voltage.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
In this example, the worst-case temperature coefficient (TEMPCO)
over 40癈 to +85癈 is assumed to be 15% for an X5R dielectric.
The tolerance of the capacitor (TOL) is assumed to be 10%, and
COUT is 9.2481 糉 at 1.8 V, as shown in Figure 61.
Substituting these values in the equation yields
CEFF = 9.2481 糉 ?(1 0.15) ?(1 0.1) = 7.0747 糉
To guarantee the performance of the buck, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
0
2
4
6
8
10
12
0
1
2
3
4
5
6
DC BIAS VOLTAGE V
Figure 61. Typical Capacitor Performance
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ADT6402SRJZ-RL7
IC TEMP SENS TRIP PT PP SOT-23-6
ADT6501SRJZP085RL7
IC TEMP SENSOR MICROPWR SOT23-5
ADT7302ARTZ-500RL7
IC SENSOR TEMP 13BIT DGT SOT23-6
ADT7310TRZ
IC TEMP SENSOR 16BIT SPI 8SOIC
ADT7461AARMZ-R
IC TEMP SENSOR DGTL 2CH 8-MSOP
ADT7461ARMZ-2R
IC TEMP SENSOR DGTL 2CH 8-MSOP
ADT7463ARQZ-REEL
IC REMOTE THERMAL CTRLR 24-QSOP
ADT7476AARQZ-R
IC REMOTE THERMAL CTLR 24QSOP
相关代理商/技术参数
ADP5042CP-1-EVALZ
功能描述:电源管理IC开发工具 Output Buck Regulator + Dual Fixed Eval RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
ADP5042CP-2-EVALZ
功能描述:电源管理IC开发工具 Output Buck Regulator + Dual Fixed Eval RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
ADP5043ACPZ-1-R7
功能描述:IC REG DL BUCK/LINEAR 20LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
ADP5043CP-1-EVALZ
功能描述:BOARD EVAL ADP5043CP-1 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ADP50450003CBZR
制造商:Analog Devices 功能描述:
ADP50460008CBZR
制造商:Analog Devices 功能描述:
ADP5050
制造商:AD 制造商全称:Analog Devices 功能描述:5-Channel Integrated Power Solution with Quad Buck Regulators and 200 mA LDO Regulator
ADP5050ACPZ-R7
功能描述:PMIC 解决方案 Adj 12V uPMU 4Buck+LDO+I2C I/F
RoHS:否 制造商:IDT 安装风格: 封装 / 箱体: 封装: